200-101 130 Questions Interconnecting Cisco Networking Devices Part 2 (ICND2)

What can be done to secure the virtual terminal interfaces on a router?

What can be done to secure the virtual terminal interfaces on a router? (Choose two.)
A. Administratively shut down the interface.
B. Physically secure the interface.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D. Configure a virtual terminal password and login process.
E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.


Answer Clike
What value will OSPF use as its router ID?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_319
If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?
A. 192.168.1.1
B. 172.16.1.1
C. 1.1.1.1
D. 2.2.2.2


Answer Clike
What are three factors a network administrator must consider before implementing Netflow in the network?

What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)
A. CPU utilization
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation


Answer Clike
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?

What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop


Answer Clike
What command visualizes the general NetFlow data on the command line?

What command visualizes the general NetFlow data on the command line?
A. show ip flow export
B. show ip flow top-talkers
C. show ip cache flow
D. show mls sampling
E. show mls netflow ip


Answer Clike
A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30.

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_312
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_313


Answer Clike
A new switch is being added to the River Campus LAN. You will work to complete this process by first configuring the building_2 switch with an IP address and default gateway. For the switch host address, you should use the last available IP address on the management subnet. In addition, the switch needs to be configured to be in the same VTP domain as the building_1 switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP configuration on building_1 are complete and correct. The configuration of the router is not accessible for this exercise. You must accomplish the following tasks:

A new switch is being added to the River Campus LAN. You will work to complete this process by first configuring the building_2 switch with an IP address and default gateway. For the switch host address, you should use the last available IP address on the management subnet. In addition, the switch needs to be configured to be in the same VTP domain as the building_1 switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP configuration on building_1 are complete and correct. The configuration of the router is not accessible for this exercise. You must accomplish the following tasks:
Determine and configure the IP host address of the new switch. Determine and configure the default gateway of the new switch. Determine and configure the correct VTP domain name for the new switch.
Configure the new switch as a VTP client
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_308


Answer Clike
A sporting goods manufacturer has decided to network three (3) locations to improve efficiency in inventory control. The routers have been named to reflect the location: Boston, Frankfurt, and Lancaster.

A sporting goods manufacturer has decided to network three (3) locations to improve efficiency in inventory control. The routers have been named to reflect the location: Boston, Frankfurt, and Lancaster.
The necessary networking has been completed at each location, and the routers have been configured with single area OSPF as the routing protocol. The Boston router was recently installed but connectivity is not complete because of incomplete routing tables. Identify and correct any problem you see in the configuration.
Note: The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_303


Answer Clike
Lab – Access List Simulation

Lab – Access List Simulation
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply a numbered access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords have been temporarily set to 鈥渃isco鈥?
The Core connection uses an IP address of 198.18.196.65
The computers in the Hosts LAN have been assigned addresses of 192.168.33.1 鈥?92.168.33.254
Host A 192.168.33.1
Host B 192.168.33.2
Host C 192.168.33.3
Host D 192.168.33.4
The servers in the Server LAN have been assigned addresses of 172.22.242.17 鈥?172.22.242.30
The Finance Web Server is assigned an IP address of 172.22.242.23.
The Public Web Server is assigned an IP address of 172.22.242.17
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_299


Answer Clike
Attention:

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_293
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_294
Attention:
In practical examinations, please note the following, the actual information will prevail.
1. Name of the router is xxx
2. Enable secret password is xxx
3. Password In access user EXEC mode using the console is xxx
4. The password to allow telnet access to the router is xxx
5. IP information


Answer Clike
Select and Place:

Select and Place:
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_291


Answer Clike
Which two statements about using the CHAP authentication mechanism in a PPP link are true?

Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.)
A. CHAP uses a two-way handshake.
B. CHAP uses a three-way handshake.
C. CHAP authentication periodically occurs after link establishment.
D. CHAP authentication passwords are sent in plaintext.
E. CHAP authentication is performed only upon link establishment.
F. CHAP has no protection from playback attacks.


Answer Clike
What are two characteristics of Frame Relay point-to-point subinterfaces?

What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)
A. They create split-horizon issues.
B. They require a unique subnet within a routing domain.
C. They emulate leased lines.
D. They are ideal for full-mesh topologies.
E. They require the use of NBMA options when using OSPF.


Answer Clike
What occurs on a Frame Relay network when the CIR is exceeded?

What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.


Answer Clike
Which two options are valid WAN connectivity methods?

Which two options are valid WAN connectivity methods? (Choose two.)
A. PPP
B. WAP
C. DSL
D. L2TPv3
E. Ethernet


Answer Clike
Which command should be used to create this map?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_042
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_043
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_044
A static map to the S-AMER location is required. Which command should be used to create this map?
A. frame-relay map ip 172.30.0.3 825 broadcast
B. frame-relay map ip 172.30.0.3 230 broadcast
C. frame-relay map ip 172.30.0.3 694 broadcast
D. frame-relay map ip 172.30.0.3 387 broadcast


Answer Clike
Which connection uses the default encapsulation for serial interfaces on Cisco routers?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_042
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_043
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_044
Which connection uses the default encapsulation for serial interfaces on Cisco routers?
A. The serial connection to the NorthCoast branch office.
B. The serial connection to the North branch office.
C. The serial connection to the Southlands branch office.
D. The serial connection to the Multinational Core.


Answer Clike
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 4
C. 16
D. unlimited


Answer Clike
Which two statements are true about the loopback address that is configured on RouterB?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_278
Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.


Answer Clike
What set of commands will properly configure the Core router?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_275
The network associate is configuring OSPF on the Core router. All the connections to the branches should be participating in OSPF. The link to the ISP should NOT participate in OSPF and should only be advertised as the default route. What set of commands will properly configure the Core router?
A. Core(config-router)# default-information originate
Core(config-router)# network 10.0.0.0 0.255.255.255 area 0 Core(config-router)# exit
Core(config-router)# network 10.10.2.13 0.0.0.242 area 0 Core(config-router)# exit
Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14
B. Core(config-router)# default-information originate
Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14
C. Core(config-router)# default-information originate
Core(config-router)# network 10.10.2.16 0.0.0.15 area 0 Core(config-router)# exit
Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14
D. Core(config-router)# default-information originate
Core(config-router)# network 10.10.2.32 0.0.0.31 area 0 Core(config-router)# exit
Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14


Answer Clike
Which statements are true about EIGRP successor routes?

Which statements are true about EIGRP successor routes? (Choose two.)
A. A successor route is used by EIGRP to forward traffic to a destination.
B. Successor routes are saved in the topology table to be used if the primary route fails.
C. Successor routes are flagged as ‘active’ in the routing table.
D. A successor route may be backed up by a feasible successor route.
E. Successor routes are stored in the neighbor table following the discovery process.


Answer Clike
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?

Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load


Answer Clike
Which statement is true, as relates to classful or classless routing?

Which statement is true, as relates to classful or classless routing?
A. Classful routing protocols send the subnet mask in routing updates.
B. RIPv1 and OSPF are classless routing protocols.
C. Automatic summarization at classful boundaries can cause problems on discontiguous subnets.
D. EIGRP and OSPF are classful routing protocols and summarize routes by default.


Answer Clike
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?

What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
A. SNMP
B. Netflow
C. WCCP
D. IP SLA


Answer Clike
Which command is used to display the collection of OSPF link states?

Which command is used to display the collection of OSPF link states?
A. show ip ospf link-state
B. show ip ospf lsa database
C. show ip ospf neighbors
D. show ip ospf database


Answer Clike
What information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_264
The network is converged. After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?
A. O 208.149.23.64 [110/13] via 190.173.23.10, 00:00:07, FastEthernet 0/0 O 208.149.23.96 [110/13] via 190.173.23.10, 00:00:16, FastEthernet 0/0
B. O 208.149.23.64 [110/1] via 190.172.23.10, 00:00:07, Serial 1/0 O 208.149.23.96 [110/3] via 190.173.23.10, 00:00:16, FastEthernet 0/0
C. O 208.149.23.64 [110/13] via 190.172.23.10, 00:00:07, Serial 1/0 O 208.149.23.96 [110/13] via 190.172.23.10, 00:00:16, Serial 1/0 O 208.149.23.96 [110/13] via 190.173.23.10, 00:00:16, FastEthernet 0/0
D. O 208.149.23.64 [110/3] via 190.172.23.10, 00:00:07, Serial 1/0 O 208.149.23.96 [110/3] via 190.172.23.10, 00:00:16, Serial 1/0


Answer Clike
What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active status?

What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active status?
A. It routes all traffic that is addressed to the destination network to the interface indicated in the routing table.
B. It sends a copy of its neighbor table to all adjacent routers.
C. It sends a multicast query packet to all adjacent neighbors requesting available routing paths to the destination network.
D. It broadcasts Hello packets to all routers in the network to re-establish neighbor adjacencies.


Answer Clike
Which routers are likely to have been elected as DR?

The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_004
Which routers are likely to have been elected as DR? (Choose two.)
A. Corp-1
B. Corp-2
C. Corp-3
D. Corp-4
E. Branch-1
F. Branch-2


Answer Clike
What router ID will OSPF use for this router?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_259
Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?
A. 10.1.1.2
B. 10.154.154.1
C. 172.16.5.1
D. 192.168.5.3


Answer Clike
How will router R2 be affected by the configuration of R1 that is shown in the exhibit?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_257
Assume that all of the router interfaces are operational and configured correctly. How will router R2 be affected by the configuration of R1 that is shown in the exhibit?
A. Router R2 will not form a neighbor relationship with R1.
B. Router R2 will obtain a full routing table, including a default route, from R1.
C. R2 will obtain OSPF updates from R1, but will not obtain a default route from R1.
D. R2 will not have a route for the directly connected serial network, but all other directly connected networks will be present, as well as the two Ethernet networks connected to R1.


Answer Clike
How will the default route configured on R1 affect the operation of R2?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_255
Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?
A. Any packet destined for a network that is not directly connected to router R1 will be dropped.
B. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.
C. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.
D. The networks directly connected to router R2 will not be able to communicate with the 172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks.
E. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.


Answer Clike
What is true about this configuration?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_253
C-router is to be used as a “router-on-a-stick” to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.


Answer Clike
What type of link is needed between Sw-A and Sw-B so host C and host D can communicate through Sw-A to the servers?

Refer to the topology.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_246
What type of link is needed between Sw-A and Sw-B so host C and host D can communicate through Sw-A to the servers?
A. trunk
B. access
C. multi-access
D. straight-through


Answer Clike
What is the TTL value for that ping?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_242
Host A pings interface S0/0 on router 3, what is the TTL value for that ping?
A. 253
B. 252
C. 255
D. 254


Answer Clike
What will the router consider the most reliable information about the path to that network?

A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network?
A. an OSPF update for network 192.168.0.0/16
B. a static route to network 192.168.10.0/24
C. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop
D. a RIP update for network 192.168.10.0/24
E. a directly connected interface with an address of 192.168.10.254/24
F. a default route with a next hop address of 192.168.10.1


Answer Clike
What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_237
What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?
A. The Serial0/0 interface is passing traffic.
B. The DLCI 100 was dynamically allocated by the router
C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server
D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud
E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP


Answer Clike
Which two statements describe the process identifier that is used in the command to configure OSPF on a router?

Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.


Answer Clike
Which three of these statements regarding 802.1Q trunking are correct?

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)
A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.


Answer Clike
Which two statements are true about interVLAN routing in the topology that is shown in the exhibit?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_233
Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.


Answer Clike
What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_231
What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)
A. Router(config)# interface fastethernet 0/0
Router(config-if)# ip address 192.168.1.1 255.255.255.0 Router(config-if)# no shut down
B. Router(config)# interface fastethernet 0/0
Router(config-if)# no shut down
Router(config)# interface fastethernet 0/0.1
Router(config-subif)# encapsulation dot1q 10
Router(config-subif)# ip address 192.168.10.1 255.255.255.0 Router(config)# interface fastethernet 0/0.2
Router(config-subif)# encapsulation dot1q 20
Router(config-subif)# ip address 192.168.20.1 255.255.255.0
C. Router(config)# router eigrp 100
Router(config-router)# network 192.168.10.0
Router(config-router)# network 192.168.20.0
D. Switch1(config)# vlan database
Switch1(config-vlan)# vtp domain XYZ
Switch1(config-vlan)# vtp server
E. Switch1(config)# interface fastethernet 0/1
Switch1(config-if)# switchport mode trunk
F. Switch1(config)# interface vlan 1
Switch1(config-if)# ip default-gateway 192.168.1.1


Answer Clike
What will be the result of making this change on Sw11?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_227
A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. Based on the output from the show vlan brief command issued on Sw12, what will be the result of making this change on Sw11?
A. Only the hosts in VLAN 1 on the two switches will be able to communicate with each other.
B. The hosts in all VLANs on the two switches will be able to communicate with each other.
C. Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other.
D. Hosts will not be able to communicate between the two switches.


Answer Clike
Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state?

Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state?
A. converged
B. redundant
C. provisioned
D. spanned


Answer Clike
What are two enhancements that OSPFv3 supports over OSPFv2?

What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.


Answer Clike
What can cause two OSPF neighbors to be stuck in the EXSTART state?

What can cause two OSPF neighbors to be stuck in the EXSTART state?
A. There is a low bandwidth connection between neighbors.
B. The neighbors have different MTU settings.
C. The OSPF interfaces are in a passive state.
D. There is only layer one connectivity between neighbors.


Answer Clike
Refer to the exhibit.

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_223
The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?
R3# show ip route
Gateway of last resort is not set
192 168.20.0/24 is variably subnetted, 6 subnets, 2 masks D 192.168.20.64/26 [90/2195456] via 192.168.20.9, 00:03:31, Serial0/0 D 192.168.20.0/30 [90/2681856] via 192.168.20.9, 00:03:31, Serial0/0 C 192.168.20.4/30 is directly connected, Serial0/1
C 192.168.20.8/30 is directly connected, Serial0/0
C 192.168.20.192/26 is directly connected, FastEthernet0/0 D 192.168.20.128/26 [90/2195456] via 192.168.20.5,00:03:31, Serial0/1
A. The path of the packets will be R3 to R2 to R1
B. The path of the packets will be R3 to R1 to R2
C. The path of the packets will be both R3 to R2 to R1 and R3 to R1
D. The path of the packets will be R3 to R1


Answer Clike
Which of the following are required to solve this?

It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three)
A. configure static frame relay map entries for each subinterface network.
B. remove the ip address from the physical interface
C. create the virtual interfaces with the interface command
D. configure each subinterface with its own IP address
E. disable split horizon to prevent routing loops between the subinterface networks
F. encapsulate the physical interface with multipoint PPP


Answer Clike
What are two characteristics of a switch that is configured as a VTP client?

What are two characteristics of a switch that is configured as a VTP client? (Choose two.)
A. If a switch that is configured to operate in client mode cannot access a VTP server, then the switch reverts to transparent mode.
B. On switches that are configured to operate in client mode, VLANs can be created, deleted, or renamed locally.
C. The local VLAN configuration is updated only when an update that has a higher configuration revision number is received.
D. VTP advertisements are not forwarded to neighboring switches that are configured in VTP transparent mode.
E. VTP client is the default VTP mode.
F. When switches in VTP client mode are rebooted, they send a VTP advertisement request to the VTP servers.


Answer Clike
Which ACL can be used?

A network engineer wants to allow a temporary entry for a remote user with a specific username and password so that the user can access the entire network over the Internet. Which ACL can be used?
A. standard
B. extended
C. dynamic
D. reflexive


Answer Clike
What can be done to address this problem?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_215
Router4 can ping Router5 (172.16.6.5), but not Router7 (172.16.11.7). There are no routing protocols running in any of the routers, and Router4 has Router6 as its default gateway. What can be done to address this problem?
A. Convert to static NAT.
B. Convert to dynamic NAT.
C. Add a static route in Router7 back to Router4.
D. Change the inside and outside NAT commands.


Answer Clike
What is the result of setting the no login command?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_213
What is the result of setting the no login command?
A. Both SSH and Telnet access is denied.
B. Both SSH and Telnet access requires a password.
C. Both SSH and Telnet access requires a new password at first login.
D. There is a virtually limitless supply of IP addresses.
E. All telnet and SSH connections will be allowed without a password


Answer Clike
What is the default gateway for host A?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_211
Host A has tested connectivity to a remote network. What is the default gateway for host A?
A. 10.16.176.1
B. 192.168.1.6
C. 192.168.1.1
D. 172.16.182.1


Answer Clike
Which command allows you to see output from the OSPF debug command?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_209
You are connected to the router as user Mike. Which command allows you to see output from the OSPF debug command?
A. terminal monitor
B. show debugging
C. show sessions
D. show ip ospf interface


Answer Clike
Which three statements are true?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_207
The output that is shown is generated at a switch. Which three statements are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.


Answer Clike
What is one benefit of PVST+?

What is one benefit of PVST+?
A. PVST+ supports Layer 3 load balancing without loops.
B. PVST+ reduces the CPU cycles for all the switches in the network.
C. PVST+ allows the root switch location to be optimized per VLAN.
D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage.


Answer Clike
At which layer of the OSI model is RSTP used to prevent loops?

At which layer of the OSI model is RSTP used to prevent loops?
A. physical
B. data link
C. network
D. transport


Answer Clike
Which access layer switch port will assume the discarding role?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_201
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2


Answer Clike
Which switch provides the spanning-tree designated port role for the network segment that services the printers?

Refer to the exhibit
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_199
.
Which switch provides the spanning-tree designated port role for the network segment that services the printers?
A. Switch1
B. Switch2
C. Switch3
D. Switch4


Answer Clike
Why has this switch not been elected the root bridge for VLAN1?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_196
Why has this switch not been elected the root bridge for VLAN1?
A. It has more than one interface that is connected to the root network segment.
B. It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C. It has a higher MAC address than the elected root bridge.
D. It has a higher bridge ID than the elected root bridge.


Answer Clike
Which two ACL statements, when combined, are the best for accomplishing this task?

A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks 192.168.146.0, 192.168.147.0, 192.168.148.0, and 192.168.149.0 only. Which two ACL statements, when combined, are the best for accomplishing this task? (Choose two.)
A. access-list 10 permit ip 192.168.146.0 0.0.1.255
B. access-list 10 permit ip 192.168.147.0 0.0.255.255
C. access-list 10 permit ip 192.168.148.0 0.0.1.255
D. access-list 10 permit ip 192.168.149.0 0.0.255.255
E. access-list 10 permit ip 192.168.146.0 0.0.0.255
F. access-list 10 permit ip 192.168.146.0 255.255.255.0


Answer Clike
In which solution is a router ACL used?

In which solution is a router ACL used?
A. filtering packets that are passing through a router
B. to change the default administrative distance of a route in the route table
C. protecting a server from unauthorized access
D. controlling path selection, based on the route metric


Answer Clike
Which IPsec security protocol should be used when confidentiality is required?

Which IPsec security protocol should be used when confidentiality is required?
A. MD5
B. PSK
C. AH
D. ESP


Answer Clike
What action does the router take?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_176
A packet with a source IP address of 192.168.2.4 and a destination IP address of 10.1.1.4 arrives at the AcmeB router. What action does the router take?
A. forwards the received packet out the Serial0/0 interface
B. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface
C. forwards a packet containing an ICMP message out the FastEthemet0/0 interface
D. forwards a packet containing an ARP request out the FastEthemet0/1 interface


Answer Clike
What is a valid HSRP virtual MAC address?

What is a valid HSRP virtual MAC address?
A. 0000.5E00.01A3
B. 0007.B400.AE01
C. 0000.0C07.AC15
D. 0007.5E00.B301


Answer Clike
Which of these represents an IPv6 link-local address?

Which of these represents an IPv6 link-local address?
A. FE80::380e:611a:e14f:3d69
B. FE81::280f:512b:e14f:3d69
C. FEFE:0345:5f1b::e14d:3d69
D. FE08::280e:611:a:f14f:3d69


Answer Clike
What are two valid reasons for adopting IPv6 over IPv4?

The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)
A. no broadcast
B. change of source address in the IPv6 header
C. change of destination address in the IPv6 header
D. Telnet access does not require a password
E. autoconfig
F. NAT


Answer Clike
Which two commands would provide information about which version of RIP was being sent and received on an interface?

An administrator is troubleshooting a problem between routers that are using different versions of RIP. Which two commands would provide information about which version of RIP was being sent and received on an interface? (Choose two.)
A. show ip protocols
B. show ip route rip
C. show interfaces
D. debug rip routing
E. debug ip rip


Answer Clike
What is a possible cause of the problem?

A department decides to replace its hub with a Catalyst 2950 switch that is no longer needed by another department. To prepare the switch for installation, the network administrator has erased the startup configuration and reloaded the switch. However, PCs that are connected to the switch experience various connectivity problems. What is a possible cause of the problem?
A. The VLAN database was not erased.
B. The management VLAN is disabled
C. The running configuration should have been erased.
D. The “mode” button was not pressed when the switch was reloaded.
E. The switch was not configured with an IP address or a default gateway.


Answer Clike
Which PPP subprotocol negotiates authentication options?

Which PPP subprotocol negotiates authentication options?
A. NCP
B. ISDN
C. SLIP
D. LCP
E. DLCI


Answer Clike
What address will EIGRP use as its router ID?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_147
If the router R1 returns the given output and has not had its router ID set manually, what address will EIGRP use as its router ID?
A. 192.168.1.2
B. 172.16.4.1
C. 192.168.10.2
D. 1.1.1.1


Answer Clike
Which statement describes an EIGRP feasible successor route?

Which statement describes an EIGRP feasible successor route?
A. A primary route, added to the routing table
B. A backup route, added to the routing table
C. A primary route, added to the topology table
D. A backup route, added to the topology table


Answer Clike
What address is a feasible successor?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_144
What address is a feasible successor?
A. 172.16.4.0
B. 10.1.4.4
C. 10.1.2.2
D. 172.16.3.0


Answer Clike
Which IP addresses would be assigned to the interfaces with point- to-point PVCs?

In the Frame Relay network, which IP addresses would be assigned to the interfaces with point- to-point PVCs?
A. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.10.3/24
B. DLCI 16 192.168.10.1 /24
DLCI 17 192.168.11.1/24
DLCI 99 192.168.12.1/24
DLCI 28 192.168.13.1/24
C. DLCI 16 192.168.10.1/24
DLCI 17 192.168.11.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.11.2/24
D. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.2/24
DLCI 99 192.168.10.3/24
DLCI 28 192.168.10.4/24


Answer Clike
Which of the following statements is true concerning this command?

The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?
A. This command should be executed from the global configuration mode.
B. The IP address 10.121.16.8 is the local router port used to forward data.
C. 102 is the remote DLCI that will receive the information.
D. This command is required for all Frame Relay configurations.
E. The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC.


Answer Clike
Which three statements about RSTP are true?

Which three statements about RSTP are true? (Choose three.)
A. RSTP significantly reduces topology reconverging time after a link failure.
B. RSTP expands the STP port roles by adding the alternate and backup roles.
C. RSTP port states are blocking, discarding, learning, or forwarding.
D. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
E. RSTP also uses the STP proposal-agreement sequence.
F. RSTP uses the same timer-based process as STP on point-to-point links.


Answer Clike
Which two states are the port states when RSTP has converged?

Which two states are the port states when RSTP has converged? (Choose two.)
A. discarding
B. listening
C. learning
D. forwarding
E. disabled


Answer Clike
Which port state is introduced by Rapid-PVST?

Which port state is introduced by Rapid-PVST?
A. learning
B. listening
C. discarding
D. forwarding


Answer Clike
Which three of these show the correct RSTP port roles for the indicated switches and interfaces?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_133
Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)
A. SwitchA, Fa0/2, designated
B. SwitchA, Fa0/1, root
C. SwitchB, Gi0/2, root
D. SwitchB, Gi0/1, designated
E. SwitchC, Fa0/2, root
F. SwitchD, Gi0/2, root


Answer Clike
Which two of these statements regarding RSTP are correct?

Which two of these statements regarding RSTP are correct? (Choose two.)
A. RSTP cannot operate with PVST+.
B. RSTP defines new port roles.
C. RSTP defines no new port states.
D. RSTP is a proprietary implementation of IEEE 802.1D STP.
E. RSTP is compatible with the original IEEE 802.1D STP.


Answer Clike
What is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_128
Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?
A. This switch has more than one interface connected to the root network segment in VLAN 2.
B. This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C. This switch interface has a higher path cost to the root bridge than another in the topology.
D. This switch has a lower bridge ID for VLAN 2 than the elected designated switch.


Answer Clike
Select and Place:

Select and Place:
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_125


Answer Clike
Select and Place:

Select and Place:
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_123


Answer Clike
Select and Place:

Select and Place:
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_120


Answer Clike
What are three reasons to collect Netflow data on a company network?

What are three reasons to collect Netflow data on a company network? (Choose three.)
A. To identify applications causing congestion
B. To authorize user network access
C. To report and alert link up / down instances
D. To diagnose slow network performance, bandwidth hogs, and bandwidth utilization
E. To detect suboptimal routing in the network
F. To confirm the appropriate amount of bandwidth that has been allocated to each Class of Service


Answer Clike
What Netflow component can be applied to an interface to track IPv4 traffic?

What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter


Answer Clike
What is the purpose of LCP?

What is the purpose of LCP?
A. to perform authentication
B. to negotiate control options
C. to encapsulate multiple protocols
D. to specify asynchronous versus synchronous


Answer Clike
Which feature does PPP use to encapsulate multiple protocols?

Which feature does PPP use to encapsulate multiple protocols?
A. NCP
B. LCP
C. IPCP
D. IPXP


Answer Clike
Which statement describes DLCI 17?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_115
Which statement describes DLCI 17?
A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.


Answer Clike
What are three benefits of GLBP?

What are three benefits of GLBP? (Choose three.)
A. GLBP supports up to eight virtual forwarders per GLBP group.
B. GLBP supports clear text and MD5 password authentication between GLBP group members.
C. GLBP is an open source standardized protocol that can be used with multiple vendors.
D. GLBP supports up to 1024 virtual routers.
E. GLBP can load share traffic across a maximum of four routers.
F. GLBP elects two AVGs and two standby AVGs for redundancy.


Answer Clike
What are the benefit of using Netflow?

What are the benefit of using Netflow? (Choose three.)
A. Network, Application & User Monitoring
B. Network Planning
C. Security Analysis
D. Accounting/Billing


Answer Clike
Why are the pings failing?

Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_082
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_083
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_084
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_085
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_086
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_087
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_088
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_089
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_090
Study the following output taken on R1:
R1# Ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5.100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
Why are the pings failing?
A. The network statement is missing on R5.
B. The loopback interface is shut down on R5.
C. The network statement is missing on R1.
D. The IP address that is configured on the Lo1 interface on R5 is incorrect.


Answer Clike
What is the cause for this misconfiguration?

Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_082
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_083
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_084
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_085
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_086
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_087
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_088
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_089
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_090
Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
A. The K values mismatch.
B. The AS does not match.
C. The network command is missing.
D. The passive-interface command is enabled.


Answer Clike
Which path does traffic take from R1 to R5?

Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_082
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_083
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_084
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_085
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_086
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_087
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_088
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_089
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_090
Which path does traffic take from R1 to R5?
A. The traffic goes through R2.
B. The traffic goes through R3.
C. The traffic is equally load-balanced over R2 and R3.
D. The traffic is unequally load-balanced over R2 and R3.


Answer Clike
Which three EIGRP routes will be present in the router R4’s routing table?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_079
Which three EIGRP routes will be present in the router R4’s routing table? (Choose three.)
A. 172.16.1.0/24
B. 10.1.10.0/30
C. 10.0.0.0/8
D. 10.1.11.0/30
E. 172.16.0.0/16
F. 192.168.1.0/24


Answer Clike
Which statement describes the process ID that is used to run OSPF on a router?

Which statement describes the process ID that is used to run OSPF on a router?
A. It is globally significant and is used to represent the AS number.
B. It is locally significant and is used to identify an instance of the OSPF database.
C. It is globally significant and is used to identify OSPF stub areas.
D. It is locally significant and must be the same throughout an area.


Answer Clike
What OSPF command, when configured, will include all interfaces into area 0?

What OSPF command, when configured, will include all interfaces into area 0?
A. network 0.0.0.0 255.255.255.255 area 0
B. network 0.0.0.0 0.0.0.0 area 0
C. network 255.255.255.255 0.0.0.0 area 0
D. network all-interfaces area 0


Answer Clike
Which router will respond to client ARP requests?

In GLBP, which router will respond to client ARP requests?
A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
B. All GLBP member routers will reply in round-robin fashion.
C. The active virtual gateway will reply with its own hardware MAC address.
D. The GLBP member routers will reply with one of four possible burned in hardware addresses.


Answer Clike
Refer to the exhibit.

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_072
The show interfaces serial 0/1 command was issued on the R10-1 router. Based on the output displayed which statement is correct?
A. The cable connected to the serial 0/1 interface of the R10-1 router is a DTE cable.
B. The R10-1 router can ping the router interface connected to the serial 0/1 interface.
C. The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000 bits per second.
D. The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service provider.
E. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation.


Answer Clike
How should the network administrator configure the serial interface of the main office router to make the connection?

A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# authentication chap
Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf
Main(config-if)# no shut


Answer Clike
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?

Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?
A. IETF
B. ANSI Annex D
C. Q9333-A Annex A
D. HDLC


Answer Clike
Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms?

Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms?
A. HDLC
B. PPP
C. X.25
D. Frame Relay


Answer Clike
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?

Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap


Answer Clike
What can be done to Frame Relay to resolve split-horizon issues?

What can be done to Frame Relay to resolve split-horizon issues?(Choose two.)
A. Disable Inverse ARP.
B. Create a full-mesh topology.
C. Develop multipoint subinterfaces.
D. Configure point-to-point subinterfaces.
E. Remove the broadcast keyword from the frame-relay map command.


Answer Clike
Which statements represent what is shown?

Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active
The command show frame-relay map gives the following output:
Which statements represent what is shown?(Choose three.)
A. 192.168.151.4 represents the IP address of the remote router
B. 192.168.151.4 represents the IP address of the local serial interface
C. DLCI 122 represents the interface of the remote serial interface
D. DLCI 122 represents the local number used to connect to the remote address
E. broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC
F. active indicates that the ARP process is working


Answer Clike
At which layer of the OSI model does PPP perform?

At which layer of the OSI model does PPP perform?
A. Layer 2
B. Layer 3
C. Layer 4
D. Layer 5


Answer Clike
Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?

Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP


Answer Clike
Which two statistics appear in show frame-relay map output?

Which two statistics appear in show frame-relay map output? (Choose two.)
A. the number of BECN packets that are received by the router
B. the value of the local DLCI
C. the number of FECN packets that are received by the router
D. the status of the PVC that is configured on the router
E. the IP address of the local router


Answer Clike
What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology?

A. It avoids split-horizon issues with distance vector routing protocols.
B. IP addresses can be conserved if VLSM is not being used for subnetting.
C. A multipoint interface offers greater security compared to point-to-point subinterface configurations.
D. The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations.


Answer Clike
What is the purpose of Inverse ARP?

What is the purpose of Inverse ARP?
A. to map a known IP address to a MAC address
B. to map a known DLCI to a MAC address
C. to map a known MAC address to an IP address
D. to map a known DLCI to an IP address
E. to map a known IP address to a SPID
F. to map a known SPID to a MAC address


Answer Clike
What password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_042
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_043
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_044
If required, what password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router?
A. No password is required.
B. Enable
C. Secret
D. Telnet
E. Console


Answer Clike
Which address will the OSPF process select as the router ID?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_035
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_036
R1 is configured with the default configuration of OSPF.
From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID?
A. 192.168.0.1
B. 172.16.1.1
C. 172.16.2.1
D. 172.16.2.225


Answer Clike
After the network has converged, what type of messaging, if any, occurs between R3 and R4?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_035
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_036
After the network has converged, what type of messaging, if any, occurs between R3 and R4?
A. No messages are exchanged.
B. Hellos are sent every 10 seconds.
C. The full database from each router is sent every 30 seconds.
D. The routing table from each router is sent every 60 seconds.


Answer Clike
How many networks will be in the routing table of R1 that are indicated to be learned by OSPF?

200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_035
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_036
OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?
A. 2
B. 3
C. 4
D. 5
E. 6
F. 7


Answer Clike
What are two possible reasons for the failure?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_033
Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)
A. The cable that is connected to S0/0 on RouterA is faulty.
B. Interface S0/0 on RouterB is administratively down.
C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.


Answer Clike
What is the operational status of the interfaces of R2 as indicated by the command output shown?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_031
Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?
A. One interface has a problem.
B. Two interfaces have problems.
C. The interfaces are functioning correctly.
D. The operational status of the interfaces cannot be determined from the output shown.


Answer Clike
What three actions will the switch take when a frame with an unknown source MAC address arrives at the interface?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_029
What three actions will the switch take when a frame with an unknown source MAC address arrives at the interface? (Select three.)
A. Send an SNMP trap.
B. Send a syslog message.
C. Increment the Security Violation counter.
D. Forward the traffic.
E. Write the MAC address to the startup-config.
F. Shut down the port.


Answer Clike
Which of these correctly describes the results of port security violation of an unknown packet?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_025
Which of these correctly describes the results of port security violation of an unknown packet?
A. port enabled; unknown packets dropped; no SNMP or syslog messages
B. port enabled; unknown packets dropped; SNMP or syslog messages
C. port disabled; no SNMP or syslog messages
D. port disabled; SNMP or syslog messages


Answer Clike
What is the result of the above configuration being applied to the switch?

The following configuration is applied to a Layer 2 Switch:
interface fastethernet 0/4
switchport mode access
switchport port-security
switchport port-security mac-address 0000.1111.1111
switchport port-security maximum 2
swithcport port-security
What is the result of the above configuration being applied to the switch?
A. A host with a mac address of 0000.1111.1111 and up to two other hosts can connect to FastEthernet 0/4 simultaneously
B. A host with a mac address of 0000.1111.1111 and one other host can connect to Fast Ethernet 0/4 simultaneously
C. Violating addresses are dropped and no record of the violation is kept
D. The switch can send an SNMP message to the network management station
E. The port is effectively shutdown


Answer Clike
Which command enables IPv6 forwarding on a Cisco router?

Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor


Answer Clike
Which type of EIGRP route entry describes a feasible successor?

Which type of EIGRP route entry describes a feasible successor?
A. a backup route, stored in the routing table
B. a primary route, stored in the routing table
C. a backup route, stored in the topology table
D. a primary route, stored in the topology table


Answer Clike
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config)# router ospf 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0


Answer Clike
What information does a router running a link-state protocol use to build and maintain its topological database?

What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)
A. hello packets
B. SAP messages sent by other routers
C. LSAs from other routers
D. beacons received on point-to-point links
E. routing tables received from other link-state routers
F. TTL packets from designated routers


Answer Clike
Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_017
The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?
A. 10.0.0.0/22 is subnetted, 1 subnets
D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
B. 10.0.0.0/28 is subnetted, 1 subnets
D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
C. 10.0.0.0/30 is subnetted, 1 subnets
D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
D. 10.0.0.0/22 is subnetted, 1 subnets
D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
E. 10.0.0.0/28 is subnetted, 1 subnets
D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
F. 10.0.0.0/30 is subnetted, 1 subnets
D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1


Answer Clike
How will the router handle a packet destined for 192.0.2.156?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_015
How will the router handle a packet destined for 192.0.2.156?
A. The router will drop the packet.
B. The router will return the packet to its source.
C. The router will forward the packet via Serial2.
D. The router will forward the packet via either Serial0 or Serial1.


Answer Clike
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

Refer to the exhibit.
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_013
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?
A. AS numbers must be changed to match on all the routers
B. Loopback interfaces must be configured so a DR is elected
C. The no auto-summary command is needed on Router A and Router C
D. Router B needs to have two network statements, one for each connected network


Answer Clike
What is the default administrative distance of OSPF?

What is the default administrative distance of OSPF?
A. 90
B. 100
C. 110
D. 120


Answer Clike
Which two are advantages of static routing when compared to dynamic routing?

Which two are advantages of static routing when compared to dynamic routing? (Choose two.)
A. Configuration complexity decreases as network size increases.
B. Security increases because only the network administrator may change the routing table.
C. Route summarization is computed automatically by the router.
D. Routing tables adapt automatically to topology changes.
E. An efficient algorithm is used to build routing tables, using automatic updates.
F. Routing updates are automatically sent to neighbors.
G. Routing traffic load is reduced when used in stub network links.


Answer Clike
What are two drawbacks of implementing a link-state routing protocol?

What are two drawbacks of implementing a link-state routing protocol? (Choose two.)
A. the sequencing and acknowledgment of link-state packets
B. the requirement for a hierarchical IP addressing scheme for optimal functionality
C. the high volume of link-state advertisements in a converged network
D. the high demand on router resources to run the link-state routing algorithm
E. the large size of the topology table listing all advertised routes in the converged network


Answer Clike
Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?
A. hop count
B. administrative distance
C. link bandwidth
D. link delay
E. link cost


Answer Clike
What are three characteristics of the OSPF routing protocol?

What are three characteristics of the OSPF routing protocol? (Choose three.)
A. It converges quickly.
B. OSPF is a classful routing protocol.
C. It uses cost to determine the best route.
D. It uses the DUAL algorithm to determine the best route.
E. OSPF routers send the complete routing table to all directly attached routers.
F. OSPF routers discover neighbors before exchanging routing information.


Answer Clike
Which routers are likely to have been elected as DR?

Refer to Exhibit:
200-101-interconnecting-cisco-networking-devices-part-2-icnd2_img_004
The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router. Which routers are likely to have been elected as DR? (Choose two.)
A. Corp-1
B. Corp-2
C. Corp-3
D. Corp-4
E. Branch-1
F. Branch-2


Answer Clike