300-115 191 Questions Implementing Cisco IP Switched Networks (SWITCH v2.0)

Which version of spanning tree is appropriate to meet the company policy?

To follow the Layer 2 switching guidelines, a network engineer decides to create a separate spanning tree for every group of 10 VLANs. Which version of spanning tree is appropriate to meet the company policy?
A. MST
B. PVST+
C. RSTP
D. RPVST+
E. STP


Answer Clike
Which option describes what causes the port to go into the errdisable state?

After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.


Answer Clike
Which type of misconfiguration is a cause?

RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?
A. The RSPAN designated VLAN is missing the remote span command.
B. The local and remote RSPAN switches are configured using different session IDs.
C. The local RSPAN switch is replicating only Rx traffic to the remote switch.
D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.


Answer Clike
Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle?

Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)
A. LACP system priority
B. LACP port priority
C. interface MAC address
D. system ID
E. port number
F. hot-standby link identification number
G. interface bandwidth


Answer Clike
Which command can prevent BPDU transmission on this port?

Refer to the exhibit. When troubleshooting a network problem, a network analyzer is connected to Port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_124
A. spanning-tree portfast bpduguard enable
B. spanning-tree bpduguard default
C. spanning-tree portfast bpdufilter default
D. no spanning-tree link-type shared


Answer Clike
Which describes the default load balacing scheme used by the Gateway Load Balancing Protocol (GLBP)?

Which describes the default load balacing scheme used by the Gateway Load Balancing Protocol (GLBP)?
A. Per host using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round robin-scheme
F. Per GLBP group using a round-robin scheme


Answer Clike
What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router?

Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_122
A. Only if both tracked objects are up will this router will be available as an AVF for group 1.
B. Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
C. If both tracked objects go down and then one comes up, but the other remains down, this router will be available as an AVF for group 1.
D. This configuration is incorrect and will not have any effect on GLBP operation.
E. If the state of one tracked object goes down then this router will release its status as an AVF for group 1.


Answer Clike
Which three statements are true of a default HSRP configuration?

Which three statements are true of a default HSRP configuration? (Choose three.)
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority decrement is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.


Answer Clike
Which two statements about the HSRP priority are true?

Which two statements about the HSRP priority are true? (Choose two)
A. To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero (0).
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.


Answer Clike
What is the most likely cause of this?

Routers R1 and R2 are configured for HSRP as shown below:
Router R1:
interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100
interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21
Router R2:
interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21
interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this?
A. physical layer issues
B. no spanning tree loops
C. use of non-default HSRP timers
D. failure to set the command standby 35 preempt


Answer Clike
Which statement is true about this command?

The following command was issued on a router that is being configured as the active HSRP router.
standby ip 10.2.1.1
Which statement is true about this command?
A. This command will not work because the HSRP group information is missing
B. The HSRP MAC address will be 0000 0c07 ac00
C. The HSRP MAC address will be 0000 0c07 ac01.
D. The HSRP MAC address will be 0000.070c ad01.
E. This command will not work because the active parameter is missing


Answer Clike
Which of the following commands can be issued without interfering with the operation of loop guard?

Which of the following commands can be issued without interfering with the operation of loop guard?
A. Switch(config-if)#spanning-tree guard root
B. Switch(config-if)#spanning-tree portfast
C. Switch(config-if)#switchport mode trunk
D. Switch(config-if)#switchport mode access


Answer Clike
Which statement is correct about 802.1Q trunking?

Which statement is correct about 802.1Q trunking?
A. Both switches must be in the same VTP domain.
B. The encapsulation type of both ends of the trunk does not have to match.
C. The native VLAN on both ends of the trunk must be VLAN 1.
D. 802.1Q trunking can only be configured on a Layer 2 port.
E. In 802.1Q trunking, all VLAN packets are tagged on the trunk link, except the native VLAN.


Answer Clike
Which of the following describes the effect the “standby preempt delay minimum 50” command will have on router R1?

You administer a network that uses two routers, R1 and R2, configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows:
R1#configure terminal
R1(config)#interface fa0/0
R1(config-if)#ip address 10.10.0.5 255.255.255.0
R1(config-if)#standby 1 priority 150
R1(config-if)#standby preempt delay minimum 50
R1(config-if)#standby 1 track interface fa0/2 15
R1(config-if)#standby 1 ip 10.10.0.20
Which of the following describes the effect the “standby preempt delay minimum 50” command will have on router R1? (Select the best answer.)
A. The HSRP priority for router R1 will increase to 200.
B. Router R1 will become the standby router if the priority drops below 50.
C. The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D. Router R1 will wait 50 seconds before attempting to preempt the active router.


Answer Clike
Which of the following commands should you issue on SwitchA for the port connected to SwitchB?

You want to configure a switched internetwork with multiple VLANs as shown above. Which of the following commands should you issue on SwitchA for the port connected to SwitchB? (Select the best answer.)
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_118
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5


Answer Clike
Which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?

Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_117
A. They have been configured with the spanning-tree bpdufilter disable command.
B. They have been configured with the spanning-tree bpdufilter enable command.
C. They have been configured with the spanning-tree bpduguard disable command.
D. They have been configured with the spanning-tree bpduguard enable command.
E. They have been configured with the spanning-tree guard loop command.
F. They have been configured with the spanning-tree guard root command.


Answer Clike
Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router?

Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router? (Select the best answer.)
A. active
B. speak
C. learn
D. listen
E. init
F. standby


Answer Clike
What will be true about Switch 15?

Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct, what will be true about Switch 15?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_116
A. All ports will be in forwarding mode.
B. All ports in VLAN 10 will be in forwarding mode.
C. All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D. All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.


Answer Clike
What happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port?

Given the configuration on a switch interface, what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port?
switchport mode access
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.


Answer Clike
Which of the following actions are taken in a VLAN map that does not contain a match clause?

VLAN maps have been configured on switch R1. Which of the following actions are taken in a VLAN map that does not contain a match clause?
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.


Answer Clike
What can we conclude about interfaces Fa0/13 and Fa0/14?

Refer to the exhibit. Based upon the output of show vlan on switch CAT2, what can we conclude about interfaces Fa0/13 and Fa0/14?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_115
A. That interfaces Fa0/13 and Fa0/14 are in VLAN 1
B. That interfaces Fa0/13 and Fa0/14 are down
C. That interfaces Fa0/13 and Fa0/14 are trunk interfaces
D. That interfaces Fa0/13 and Fa0/14 have a domain mismatch with another switch
E. That interfaces Fa0/13 and Fa0/14 have a duplex mismatch with another switch


Answer Clike
Which three statements are correct with regard to the IEEE 802.1Q standard?

Which three statements are correct with regard to the IEEE 802.1Q standard? (Choose three)
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address


Answer Clike
Which two statements about the STP process for VLAN 200 are true?

Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? (Choose two.)
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_114
A. BPDUs will be sent out every two seconds.
B. The time spent in the listening state will be 30 seconds.
C. The time spent in the learning state will be 15 seconds.
D. The maximum length of time that the BPDU information will be saved is 30 seconds.
E. This switch is the root bridge for VLAN 200.
F. BPDUs will be sent out every 10 seconds.


Answer Clike
On which interface can port security be configured?

On which interface can port security be configured?
A. static trunk ports
B. destination port for SPAN
C. EtherChannel port group
D. dynamic access point


Answer Clike
Which option describes what this configuration allows?

A network engineer configures port security and 802.1x on the same interface. Which option describes what this configuration allows?
A. It allows port security to secure the MAC address that 802.1x authenticates.
B. It allows port security to secure the IP address that 802.1x authenticates.
C. It allows 802.1x to secure the MAC address that port security authenticates.
D. It allows 802.1x to secure the IP address that port security authenticates.


Answer Clike
Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?

Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?
A. sticky
B. dynamic
C. static
D. secure


Answer Clike
Which command would a network engineer apply to error-disable a switchport when a packetstorm is detected?

Which command would a network engineer apply to error-disable a switchport when a packetstorm is detected?
A. router(config-if)#storm-control action shutdown
B. router(config-if)#storm-control action trap
C. router(config-if)#storm-control action error
D. router(config-if)#storm-control action enable


Answer Clike
Which switch feature prevents traffic on a LAN from being overwhelmed by continuous multicast or broadcast traffic?

Which switch feature prevents traffic on a LAN from being overwhelmed by continuous multicast or broadcast traffic?
A. storm control
B. port security
C. VTP pruning
D. VLAN trunking


Answer Clike
Which feature must be enabled on the access VLAN for that interface?

When IP Source Guard with source IP filtering is enabled on an interface, which feature must be enabled on the access VLAN for that interface?
A. DHCP snooping
B. storm control
C. spanning-tree portfast
D. private VLAN


Answer Clike
Which database is used to determine the validity of an ARP packet based on a valid IP-to- MAC address binding?

Which database is used to determine the validity of an ARP packet based on a valid IP-to- MAC address binding?
A. DHCP snooping database
B. dynamic ARP database
C. dynamic routing database
D. static ARP database


Answer Clike
Which private VLAN can have only one VLAN and be a secondary VLAN that carries unidirectional traffic upstream from the hosts toward the promiscuous ports and the gateway?

Which private VLAN can have only one VLAN and be a secondary VLAN that carries unidirectional traffic upstream from the hosts toward the promiscuous ports and the gateway?
A. isolated VLAN
B. primary VLAN
C. community VLAN
D. promiscuous VLAN


Answer Clike
Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?

Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?
A. promiscuous port
B. isolated port
C. community port
D. trunk port


Answer Clike
What does the command vlan dot1q tag native accomplish when configured under global configuration?

What does the command vlan dot1q tag native accomplish when configured under global configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.


Answer Clike
How many VLANs can be used to carry user traffic?

When you design a switched network using VTPv2, how many VLANs can be used to carry user traffic?
A. 1000
B. 1001
C. 1024
D. 2048
E. 4095
F. 4096


Answer Clike
What is the root cause of the problem?

The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?
A. The command effectively removed all other working VLANs and replaced them with the new VLANs.
B. VTP pruning removed all unused VLANs.
C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.
D. Allowing additional VLANs across the trunk introduced a loop in the network.


Answer Clike
Which enhancement to a spanning-tree design prevents unnecessary traffic from crossing the extended LAN segment?

A network engineer is extending a LAN segment between two geographically separated data centers. Which enhancement to a spanning-tree design prevents unnecessary traffic from crossing the extended LAN segment?
A. Modify the spanning-tree priorities to dictate the traffic flow.
B. Create a Layer 3 transit VLAN to segment the traffic between the sites.
C. Use VTP pruning on the trunk interfaces.
D. Configure manual trunk pruning between the two locations.


Answer Clike
What is the problem?

After configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?
A. The VTP server must be reloaded.
B. The VTP version number must be set to version 3.
C. After each update to the VTP server, it takes up to 4 hours propagate.
D. VTP must be stopped and restarted on the server.
E. Another switch in the domain has a higher revision number than the server.


Answer Clike
Which action resolves this problem?

A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?
A. Reload the new switch.
B. Restart the VTP process on the new switch.
C. Reload the VTP server.
D. Verify connected trunk ports.


Answer Clike
Which two protocols can be automatically negotiated between switches for trunking?

Which two protocols can be automatically negotiated between switches for trunking? (Choose two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q


Answer Clike
Which two actions can prevent interface trunking?

For security reasons, the IT manager has prohibited users from dynamically establishing trunks with their associated upstream switch. Which two actions can prevent interface trunking? (Choose two.)
A. Configure trunk and access interfaces manually.
B. Disable DTP on a per interface basis.
C. Apply BPDU guard and BPDU filter.
D. Enable switchport block on access ports.


Answer Clike
Which technique allows specific VLANs to be strictly permitted by the administrator?

Which technique allows specific VLANs to be strictly permitted by the administrator?
A. VTP pruning
B. transparent bridging
C. trunk-allowed VLANs
D. VLAN access-list
E. L2P tunneling


Answer Clike
Which statement describes the outcome of this scenario?

DHCP snooping and IP Source Guard have been configured on a switch that connects to several client workstations. The IP address of one of the workstations does not match any entries found in the DHCP binding database. Which statement describes the outcome of this scenario?
A. Packets from the workstation will be rate limited according to the default values set on the switch.
B. The interface that is connected to the workstation in question will be put into the errdisabled state.
C. Traffic will pass accordingly after the new IP address is populated into the binding database.
D. The packets originating from the workstation are assumed to be spoofed and will be discarded.


Answer Clike
Which solution ensures that the server maintains network reachability in the future?

A server with a statically assigned IP address is attached to a switch that is provisioned for DHCP snooping. For more protection against malicious attacks, the network team is considering enabling dynamic ARP inspection alongside DHCP snooping. Which solution ensures that the server maintains network reachability in the future?
A. Disable DHCP snooping information option.
B. Configure a static DHCP snooping binding entry on the switch.
C. Trust the interface that is connected to the server with the ip dhcp snooping trust command.
D. Verify the source MAC address of all untrusted interfaces with ip dhcp snooping verify macaddress command.


Answer Clike
What is the default HSRP priority?

What is the default HSRP priority?
A. 50
B. 100
C. 120
D. 1024


Answer Clike
Which configuration command ties the router hot standby priority to the availability of its interfaces?

Which configuration command ties the router hot standby priority to the availability of its interfaces?
A. standby group
B. standby priority
C. backup interface
D. standby track


Answer Clike
What is the function of NSF?

What is the function of NSF?
A. forward traffic simultaneously using both supervisors
B. forward traffic based on Cisco Express Forwarding
C. provide automatic failover to back up supervisor in VSS mode
D. provide nonstop forwarding in the event of failure of one of the member supervisors


Answer Clike
Which command creates a login authentication method named “login” that will primarily use RADIUS and fail over to the local user database?

Which command creates a login authentication method named “login” that will primarily use RADIUS and fail over to the local user database?
A. (config)# aaa authentication login default radius local
B. (config)# aaa authentication login login radius local
C. (config)# aaa authentication login default local radius
D. (config)# aaa authentication login radius local


Answer Clike
Which portion of AAA looks at what a user has access to?

Which portion of AAA looks at what a user has access to?
A. authorization
B. authentication
C. accounting
D. auditing


Answer Clike
What is the solution to avoid the snooping database from being rebuilt after every device reboot?

A Cisco Catalyst switch that is prone to reboots continues to rebuild the DHCP snooping database. What is the solution to avoid the snooping database from being rebuilt after every device reboot?
A. A DHCP snooping database agent should be configured.
B. Enable DHCP snooping for all VLANs that are associated with the switch.
C. Disable Option 82 for DHCP data insertion.
D. Use IP Source Guard to protect the DHCP binding table entries from being lost upon rebooting.
E. Apply ip dhcp snooping trust on all interfaces with dynamic addresses.


Answer Clike
What is the result of the configuration?

A network engineer tries to configure storm control on an EtherChannel bundle. What is the result of the configuration?
A. The storm control settings will appear on the EtherChannel, but not on the associated physical ports.
B. The configuration will be rejected because storm control is not supported for EtherChannel.
C. The storm control configuration will be accepted, but will only be present on the physical interfaces.
D. The settings will be applied to the EtherChannel bundle and all associated physical interfaces.


Answer Clike
What is the result of the configuration?

Refer to the exhibit. What is the result of the configuration?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_107
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.


Answer Clike
Which Cisco IOS feature can be used to achieve this task?

A network engineer must improve bandwidth and resource utilization on the switches by stopping the inefficient flooding of frames on trunk ports where the frames are not needed. Which Cisco IOS feature can be used to achieve this task?
A. VTP pruning
B. access list
C. switchport trunk allowed VLAN
D. VLAN access-map


Answer Clike
Which option is the cause of the spanning-tree error?

Refer to the exhibit. A multilayer switch has been configured to send and receive encapsulated and tagged frames. VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause of the spanning-tree error?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_106
A. VLAN spanning-tree in SW-2 is configured.
B. spanning-tree bpdu-filter is enabled.
C. 802.1q trunks are on both sides, both with native VLAN mismatch.
D. VLAN ID 1 should not be used for management traffic because its unsafe.


Answer Clike
Which statement about using native VLANs to carry untagged frames is true?

Which statement about using native VLANs to carry untagged frames is true?
A. Cisco Discovery Protocol version 2 carries native VLAN information, but version 1 does not.
B. Cisco Discovery Protocol version 1 carries native VLAN information, but version 2 does not.
C. Cisco Discovery Protocol version 1 and version 2 carry native VLAN information.
D. Cisco Discovery Protocol version 3 carries native VLAN information, but versions 1 and 2 do not.


Answer Clike
Which Cisco IOS switching feature can be used to achieve the task?

A network engineer must implement Ethernet links that are capable of transporting frames and IP traffic for different broadcast domains that are mutually isolated. Consider that this is a multivendor environment. Which Cisco IOS switching feature can be used to achieve the task?
A. PPP encapsulation with a virtual template
B. Link Aggregation Protocol at the access layer
C. dot1q VLAN trunking
D. Inter-Switch Link


Answer Clike
Which action resolves this problem?

Refer to the exhibit. The network switches for two companies have been connected and manually configured for the required VLANs, but users in company A are not able to access network resources in company B when DTP is enabled. Which action resolves this problem?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_104
A. Delete vlan.dat and ensure that the switch with lowest MAC address is the VTP server.
B. Disable DTP and document the VTP domain mismatch.
C. Manually force trunking with switchport mode trunk on both switches.
D. Enable the company B switch with the vtp mode server command.


Answer Clike
Which configuration must be made before the private VLAN is configured?

A network engineer wants to ensure Layer 2 isolation of customer traffic using a private VLAN.
Which configuration must be made before the private VLAN is configured?
A. Disable VTP and manually assign VLANs.
B. Ensure all switches are configured as VTP server mode.
C. Configure VTP Transparent Mode.
D. Enable VTP version 3.


Answer Clike
Which action resolves this problem?

Refer to the exhibit. The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_103
A. Disable VTP pruning and disable 802.1q.
B. Update the VTP revision number.
C. Change VTP mode to server and enable 802.1q.
D. Enable VTP pruning and disable 802.1q.


Answer Clike
Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?

Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?
A. VTP pruning
B. port-security
C. storm control
D. bpdguard


Answer Clike
Why is the EtherChannel bundle not working?

After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/down state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?
A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.


Answer Clike
Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch?

Refer to the exhibit. A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_101
A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination
B. A remote SPAN VLAN on the distribution and access layer switch
C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination
D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination
E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination
F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination


Answer Clike
How can the traffic that is mirrored out the GigabitEthernet0/48 port be limited to only traffic that is received or transmitted in VLAN 10 on the GigabitEthernet0/1 port?

Refer to the exhibit. How can the traffic that is mirrored out the GigabitEthernet0/48 port be limited to only traffic that is received or transmitted in VLAN 10 on the GigabitEthernet0/1 port?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_100
A. Change the configuration for GigabitEthernet0/48 so that it is a member of VLAN 10.
B. Add an access list to GigabitEthernet0/48 to filter out traffic that is not in VLAN 10.
C. Apply the monitor session filter globally to allow only traffic from VLAN 10.
D. Change the monitor session source to VLAN 10 instead of the physical interface.


Answer Clike
Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?

Refer to the exhibit. Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_099
A. switch1
channel-group 1 mode active
switch2
channel-group 1 mode auto
B. switch1
channel-group 1 mode desirable
switch2
channel-group 1 mode passive
C. switch1
channel-group 1 mode on
switch2
channel-group 1 mode auto
D. switch1
channel-group 1 mode desirable
switch2
channel-group 1 mode auto


Answer Clike
What percentage of bandwidth is reduced when a stack cable is broken?

What percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100


Answer Clike
Which configuration must be added to the new switch before it can be added to the switch stack?

A network engineer wants to add a new switch to an existing switch stack. Which configuration must be added to the new switch before it can be added to the switch stack?
A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information


Answer Clike
What is the maximum number of switches that can be stacked using Cisco StackWise?

What is the maximum number of switches that can be stacked using Cisco StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_096


Answer Clike
Drag and Drop Question

Drag and Drop Question
Match the HSRP states on the left with the correct definition on the right.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_094


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_092


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_090


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_088


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_086


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_084


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_082


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_080


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_078


Answer Clike
Drag and Drop Question

Drag and Drop Question
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_076


Answer Clike
Which of the following configuration steps will allow creating private VLANs?

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_067
Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. Which of the following configuration steps will allow creating private VLANs?
A. Disable VTP pruning on SW1 only
B. Disable VTP pruning on SW2 only
C. Disable VTP pruning on SW4 only
D. Disable VTP pruning on SW2, SW4 and New_Switch
E. Disable VTP pruning on New_Switch and SW4 only.


Answer Clike
Which configuration step is valid?

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_067
You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?
A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2
B. Configure VLAN 500 and VLAN 600 on SW1 only
C. Configure VLAN 500 and VLAN 600 on SW2 only
D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
E. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.


Answer Clike
For which configured VLAN are untagged frames sent over trunk between SW1 and SW2?

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_067
Refer to the configuration. For which configured VLAN are untagged frames sent over trunk between SW1 and SW2?
A. VLAN1
B. VLAN 99
C. VLAN 999
D. VLAN 40
E. VLAN 50
F. VLAN 200
G. VLAN 300


Answer Clike
Which of the configuration is correct?

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_067
You are connecting the New_Switch to the LAN topology; the switch has been partially configured and you need to complete the rest of configuration to enable PC1 communication with PC2.
Which of the configuration is correct?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_068
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E


Answer Clike
What is the virtual mac-address of HSRP group 1?

Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_061
What is the virtual mac-address of HSRP group 1?
A. 0000.0c07.ac02
B. 4000.0000.0010
C. 0000.0c07.ac01
D. 4000.0000.ac01
E. 4000.0000.ac02
F. 0000.0c07.0010


Answer Clike
What issue is causing Router R1 and R2 to both be displayed as the HSRP active router for group 2?

Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_061
What issue is causing Router R1 and R2 to both be displayed as the HSRP active router for group 2?
A. The HSRP group number mismatch
B. The HSRP group authentication is misconfigured
C. The HSRP Hello packets are blocked
D. The HSRP timers mismatch
E. The HSRP group priorities are different


Answer Clike
Which of the statement regarding HSRP priority is true?

Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_061
Refer to the exhibit. If router R1 interface Etherne0/0 goes down and recovers, which of the statement regarding HSRP priority is true?
A. The interface will have the priority decremented by 40 for HSRP group 1.
B. The interface will have the priority decremented by 60 for HSRP group 1
C. The interface will have its current priority incremented by 40 for HSRP group 1
D. The interface will have its current priority incremented by 60 for HSRP group 1
E. The interface will default to the a priority of 100 for HSRP group 1


Answer Clike
What percentage of the outgoing traffic from the 172.16.10.0/24 subnet is being forwarded through R1?

Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_061
What percentage of the outgoing traffic from the 172.16.10.0/24 subnet is being forwarded through R1?
A. R1-0%
B. R1-50 %, R2-50%
C. R2-100%
D. R1-100%


Answer Clike
Lab Simulation – MLS and EIGRP

Lab Simulation – MLS and EIGRP
You have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram.
You need to configure SwitchC so that Hosts H1 and H2 can successfully ping the server S1.
Also SwitchC needs to be able to ping server S1.
Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links. Company policies forbid the use of static or default routing. All routes must be learned via EIGRP 65010 routing protocol.
You do not have access to RouteC. RouterC is correctly configured. No trunking has been configured on RouterC.
Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution:
– 10.10.10.0/24
– 190.200.250.32/27
– 190.200.250.64/27
Hosts H1 and H2 are configured with the correct IP address and default gateway.
SwitchC uses Cisco as the enable password.
Routing must only be enabled for the specific subnets shown in the diagram.
Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learned via the EIGRP routing protocol.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_058


Answer Clike
Hotspot – HSRP

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
If GigabitEthemet1/0/1 on DSW2 is shutdown, what will be the resulting priority value of the VLAN 105 HSRP group on router DSW2?
A. 90
B. 100
C. 150
D. 200


Answer Clike
What is the priority value of the VLAN 105 HSRP group on DSW2?

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
What is the priority value of the VLAN 105 HSRP group on DSW2?
A. 50
B. 100
C. 150
D. 200


Answer Clike
What can to be done to make the group function properly?

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1 and DSW2. All other interfaces were up. During this time, DSW1 became the active router for the VLAN 104HSRP group. As related to the VLAN 104HSRP group, what can to be done to make the group function properly?
A. On DSW1, disable preempt.
B. On DSW2, decrease the priority value to a value less than 150.
C. On DSW1, increase the decrement value in the track command to a value greater than 6.
D. On DSW1, decrease the decrement value in the track command to a value less than 1.


Answer Clike
What can be done to make the group function properly?

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
All interfaces are active. DSW2 has not become the active device for the VLAN 103 HSRP group.
As related to the VLAN 103 HSRP group, what can be done to make the group function properly?
A. On DSW1, disable preempt.
B. On DSW1, decrease the priority value to a value less than 190 and greater than 150.
C. On DSW2, increase the priority value to a value greater 200 and less than 250.
D. On DSW2, increase the decrement value in the track command to a value greater than 10 and less than 50.


Answer Clike
What needs to be done to make the group function properly?

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1. All other interfaces were up. During this time, DSW1 remained the active device for the VLAN 102 HSRP group. You have determined that there is an issue with the decrement value in the track command for the VLAN 102 HSRP group. What needs to be done to make the group function properly?
A. The decrement value on DSW1 should be greaterthan 5 and less than 15. 0
B. The decrement value on DSW1 should be greaterthan 9 and less than 15.
C. The decrement value on DSW1 should be greaterthan 11 and less than 19.
D. The decrement value on DSWTs should be greaterthan 190 and less than 200.
E. The decrement value on DSWTs should be greaterthan 195 and less than 205.


Answer Clike
What needs to be done to make the group for VLAN 101 function properly?

Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_045
During routine maintenance, GigabitEthernet1/0/1 on DSW1 was shut down. All other interfaces were up. DSW2 became the active HSRP device for VLAN 101 as desired. However, after GigabitEthemet1/0/1 on DSW1 was reactivated, DSW1 did not become the active router for VLAN 101 as desired. What needs to be done to make the group for VLAN 101 function properly?
A. Enable preempt in the VLAN 101 HSRP group on DSW1.
B. Disable preempt in the VLAN 101 HSRP group on DSW2’s.
C. In the VLAN 101 HSRP group on DSW1, decrease the priority value to avaluethatis less ‘ than the priority value configured in the VLAN 101 HSRP group on DSW2.
D. Decrease the decrement value in the track command for the VLAN 101 HSRP group on U DSWTs to a values less than the value in the track command for the VLAN 101 HSRP group on DSW2.


Answer Clike
Lab Simulation – AAAdot1x

Lab Simulation – AAAdot1x
SWITCH.com is an IT company that has an existing enterprise network comprised of two layer 2 only switches; DSW1 and ASW1. The topology diagram indicates their layer 2 mapping. VLAN 20 is a new VLAN that will be used to provide the shipping personnel access to the server.
Corporate polices do not allow layer 3 functionality to be enabled on the switches.
For security reasons, it is necessary to restrict access to VLAN 20 in the following manner:
– Users connecting to VLAN 20 via portfO/1 on ASW1 must be authenticated before they are given access to the network.
Authentication is to be done via a Radius server:
– Radius server host: 172.120.40.46
– Radius key: rad123
– Authentication should be implemented as close to the host as possible.
– Devices on VLAN 20 are restricted to the subnet of 172.120.40.0/24.
– Packets from devices in the subnet of 172.120.40.0/24 should be allowed on VLAN 20.
– Packets from devices in any other address range should be dropped on VLAN 20.
– Filtering should be implemented as close to the serverfarm as possible.
The Radius server and application servers will be installed at a future date. You have been tasked with implementing the above access control as a pre-condition to installing the servers. You must use the available IOS switch features.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_043


Answer Clike
Lab Simulation – LACP with STP Sim

Lab Simulation – LACP with STP Sim
You work for SWITCH.com. They have just added a new switch (SwitchB) to the existing network as shown in the topology diagram.
RouterA is currently configured correctly and is providing the routing function for devices on SwitchA and SwitchB. SwitchA is currently configured correctly, but will need to be modified to support the addition of SwitchB. SwitchB has a minimal configuration. You have been tasked with competing the needed configuring of SwitchA and SwitchB. SwitchA and SwitchB use Cisco as the enable password.
Configuration Requirements for SwitchA
The VTP and STP configuration modes on SwitchA should not be modified.
– SwitchA needs to be the root switch for vlans 11, 12, 13, 21, 22 and
23. All other vlans should be left are their default values.
Configuration Requirements for SwitchB
– Vlan 21
Name: Marketing will support two servers attached to fa0/9 and fa0/10
– Vlan 22
Name: Sales will support two servers attached to fa0/13 and fa0/14
– Vlan 23
Name: Engineering will support two servers attached to fa0/15 and fa0/16
– Access ports that connect to server should transition immediately to forwarding state upon detecting the connection of a device.
– SwitchB VTP mode needs to be the same as SwitchA.
– SwitchB must operate in the same spanning tree mode as SwitchA
– No routing is to be configured on SwitchB
– Only the SVI vlan 1 is to be configured and it is to use address 192.168.1.11/24
Inter-switch Connectivity Configuration Requirements
– For operational and security reasons trunking should be unconditional and Vlans 1, 21, 22 and 23 should tagged when traversing the trunk link.
– The two trunks between SwitchA and SwitchB need to be configured in a mode that allows for the maximum use of their bandwidth for all vlans. This mode should be done with a non-proprietary protocol, with SwitchA controlling activation.
– Propagation of unnecessary broadcasts should be limited using manual pruning on this trunk link.
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_039


Answer Clike
Which option describes the reason for this message in a GLBP configuration?

Refer to the exhibit. Which option describes the reason for this message in a GLBP configuration?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_37
A. Unavailable GLBP active forwarder
B. Incorrect GLBP IP address
C. HSRP configured on same interface as GLBP
D. Layer 2 loop


Answer Clike
Which command configures an HSRP group to become a slave of another HSRP group?

Which command configures an HSRP group to become a slave of another HSRP group?
A. standby slave
B. standby group track
C. standby follow
D. standby group backup


Answer Clike
Which command correctly configures standby tracking for group 1 using the default decrement priority value?

Which command correctly configures standby tracking for group 1 using the default decrement priority value?
A. standby 1 track 100
B. standby 1 track 100 decrement 1
C. standby 1 track 100 decrement 5
D. standby 1 track 100 decrement 20


Answer Clike
Which VRRP router is responsible for forwarding packets that are sent to the IP addresses of the virtual router?

Which VRRP router is responsible for forwarding packets that are sent to the IP addresses of the virtual router?
A. virtual router master
B. virtual router backup
C. virtual router active
D. virtual router standby


Answer Clike
Which gateway role is responsible for answering ARP requests for the virtual IP address in

Which gateway role is responsible for answering ARP requests for the virtual IP address in GLBP?
A. active virtual forwarder
B. active virtual router
C. active virtual gateway
D. designated router


Answer Clike
What is the maximum number of virtual MAC addresses that GLBP allows per group?

What is the maximum number of virtual MAC addresses that GLBP allows per group?
A. 2
B. 4
C. 6
D. 8


Answer Clike
What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up?

What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up?
A. 1
B. 5
C. 10
D. 15


Answer Clike
Which First Hop Redundancy Protocol is an IEEE Standard?

Which First Hop Redundancy Protocol is an IEEE Standard?
A. GLBP
B. HSRP
C. VRRP
D. OSPF


Answer Clike
Which type of port must you configure the gateway router port as?

When you configure a private VLAN, which type of port must you configure the gateway router port as?
A. promiscuous port
B. isolated port
C. community port
D. access port


Answer Clike
Which port type connects the switch to the gateway router?

When you configure private VLANs on a switch, which port type connects the switch to the gateway router?
A. promiscuous
B. community
C. isolated
D. trunked


Answer Clike
Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?

Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?
A. ip dhcp snooping trust
B. ip dhcp snooping
C. ip dhcp trust
D. ip dhcp snooping information


Answer Clike
Which switch feature determines validity based on IP-to-MAC address bindings that are stored in a trusted database?

Which switch feature determines validity based on IP-to-MAC address bindings that are stored in a trusted database?
A. Dynamic ARP Inspection
B. storm control
C. VTP pruning
D. DHCP snooping


Answer Clike
Which type of information does the DHCP snooping binding database contain?

Which type of information does the DHCP snooping binding database contain?
A. untrusted hosts with leased IP addresses
B. trusted hosts with leased IP addresses
C. untrusted hosts with available IP addresses
D. trusted hosts with available IP addresses


Answer Clike
When a network administrator is attempting an SSH connection to the device, in which order does the device check the login credentials?

Refer to the exhibit. When a network administrator is attempting an SSH connection to the device, in which order does the device check the login credentials?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_033
A. RADIUS server, local username, line password
B. RADIUS server, line password, local username
C. Line password, local username, RADIUS server
D. Line password, RADIUS server, local username


Answer Clike
Which login credentials are required when connecting to the console port in this output?

Refer to the exhibit. Which login credentials are required when connecting to the console port in this output?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_033
A. none required
B. username cisco with password cisco
C. no username with password linepass
D. login authentication default


Answer Clike
Which authentication service is needed to configure 802.1x?

Which authentication service is needed to configure 802.1x?
A. RADIUS with EAP Extension
B. TACACS+
C. RADIUS with CoA
D. RADIUS using VSA


Answer Clike
Which AAA Authorization type includes PPP, SLIP, and ARAP connections?

Which AAA Authorization type includes PPP, SLIP, and ARAP connections?
A. network
B. IP mobile
C. EXEC
D. auth-proxy


Answer Clike
Which command globally enables AAA on a device?

Which command globally enables AAA on a device?
A. aaa new-model
B. aaa authentication
C. aaa authorization
D. aaa accounting


Answer Clike
Which statement describes what happens when a switch enters dual active recovery mode?

Which statement describes what happens when a switch enters dual active recovery mode?
A. The switch shuts down and waits for the VSL link to be restored before sending traffic.
B. All interfaces are shut down in the formerly active virtual switch member, but the new active virtual switch forwards traffic on all links.
C. The switch continues to forward traffic out all links and enables spanning tree on VSL link and all other links to prevent loops.
D. The VSS detects which system was last in active state and shuts down the other switch.


Answer Clike
Which statement describes what happens if all VSL connections between the virtual switch members are lost?

Which statement describes what happens if all VSL connections between the virtual switch members are lost?
A. Both virtual switch members cease to forward traffic.
B. The VSS transitions to the dual active recovery mode, and both virtual switch members continue to forward traffic independently.
C. The virtual switch members reload.
D. The VSS transitions to the dual active recovery mode, and only the new active virtual switch continues to forward traffic.


Answer Clike
What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?

What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?
A. 4
B. 6
C. 8
D. 12


Answer Clike
Which statement about restrictions for multichassis LACP is true?

Which statement about restrictions for multichassis LACP is true?
A. It is available only on a Cisco Catalyst 6500 Series chassis.
B. It does not support 1Gb links.
C. Converting a port channel to mLACP can cause a service disruption.
D. It is not available in VSS.


Answer Clike
Which option is a benefit of using VSS?

Which option is a benefit of using VSS?
A. reduces cost
B. simplifies configuration
C. provides two independent supervisors with two different control planes
D. removes the need for a First Hop Redundancy Protocol


Answer Clike
Which statement describes what happens when a port configured with root guard receives a superior BPDU?

Which statement describes what happens when a port configured with root guard receives a superior BPDU?
A. The port goes into errdisabled state and stops forwarding traffic.
B. The port goes into BPDU-inconsistent state and stops forwarding traffic.
C. The port goes into loop-inconsistent state and stops forwarding traffic.
D. The port goes into root-inconsistent state and stops forwarding traffic.


Answer Clike
Which statement about the spanning-tree portfast feature on the switch is true?

A network engineer configured an Ethernet switch using these commands.
Switchone(config) # Spanning-tree portfast bpdufilter default
Which statement about the spanning-tree portfast feature on the switch is true?
A. If an interface is enabled for portfast receives BDPU, the port goes through the spanning-tree listening, learning, and forwarding states.
B. If an interface is enabled for portfast receives BDPU, the port does not go through the spanningtree listening, learning, and forwarding states.
C. If an interface is enabled for portfast receives BDPU, the port is shut down immediately.
D. If an interface is enabled for portfast receives BDPU, the port goes into the spanning- tree inconsistent state.


Answer Clike
Which option will be the new root port for VLAN 10?

Refer to the exhibit. All ports are members of VLAN 10. Considering the default cost of upstream bridges to the root bridge is equal, which option will be the new root port for VLAN 10?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_029
A. interface f0/13
B. interface f0/14
C. interface f0/15
D. interface f0/21


Answer Clike
Which Layer 2 enhancement can be used to eliminate this delay?

A network engineer is trying to deploy a PC on a network. The engineer observes that when the PC is connected to the network, it takes 30 to 60 seconds for the PC to see any activity on the network interface card. Which Layer 2 enhancement can be used to eliminate this delay?
A. Configure port duplex and speed to auto negotiation.
B. Configure port to duplex full and speed 1000.
C. Configure spanning-tree portfast.
D. Configure no switchport.


Answer Clike
Why would the switch be considered as a root bridge?

Refer to the exhibit. Why would the switch be considered as a root bridge?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_027
A. The bridge priority is 1 and all ports are forwarding.
B. The switch priority for VLAN 1 and the macro specifies “This Bridge is the root”.
C. The bridge priority is 128.19 and all ports are forwarding.
D. The switch priority value is zero, it has the lowest priority value for VLAN 1.


Answer Clike
Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?

Refer to the exhibit. f1/0 and f1/1 have the same end-to-end path cost to the designated bridge.
Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_025
A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.
B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.
C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.
D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.


Answer Clike
What is the total number of spanning-tree instances running on the switch?

When two MST instances (MST 1 and MST 2) are created on a switch, what is the total number of spanning-tree instances running on the switch?
A. 1
B. 2
C. 3
D. 4


Answer Clike
What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives 802.1d BPDU?

What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives 802.1d BPDU?
A. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives an 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
B. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
C. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU.
D. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.


Answer Clike
Which statement about switch S1 is true?

Refer to the exhibit. Which statement about switch S1 is true?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_023
A. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 port-channel interface using an open standard protocol.
B. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 physical port- channel interface using a Cisco proprietary protocol.
C. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 port-channel interface using a Cisco proprietary protocol.
D. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 physical port- channel interface using an open standard protocol.


Answer Clike
Which statement about using EtherChannel on Cisco IOS switches is true?

Which statement about using EtherChannel on Cisco IOS switches is true?
A. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
B. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
C. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 16 Gbps only for Gigabit EtherChannel.
D. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 10 Gbps only for Gigabit EtherChannel.


Answer Clike
Which statement describes what happens to all ports in the bundle?

A network engineer changed the port speed and duplex setting of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?
A. PAgP changes the port speed and duplex for all ports in the bundle.
B. PAgP drops the ports that do not match the configuration.
C. PAgP does not change the port speed and duplex for all ports in the bundle until the switch is rebooted.
D. PAgP changes the port speed but not the duplex for all ports in the bundle.


Answer Clike
Which action can the engineer take to resolve this issue?

Refer to the exhibit. Users of PC-1 experience slow connection when a webpage is requested from the server. To increase bandwidth, the network engineer configured an EtherChannel on interfaces Fa1/0 and Fa0/1 of the server farm switch, as shown here:
Server_Switch#sh etherchannel load-balance
EtherChannel Load-Balancing Operational State (src-mac):
Non-IP: Source MAC address
IPv4: Source MAC address
IPv6: Source IP address
Server_Switch#
However, traffic is still slow. Which action can the engineer take to resolve this issue?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_022
A. Disable EtherChannel load balancing.
B. Upgrade the switch IOS to IP services image.
C. Change the load-balance method to dst-mac.
D. Contact Cisco TAC to report a bug on the switch.


Answer Clike
Which EtherChannel negotiation protocol is configured on the interface f0/13?

Refer to the exhibit. Which EtherChannel negotiation protocol is configured on the interface f0/13 ?f0/15?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_021
A. Link Combination Control Protocol
B. Port Aggregation Protocol
C. Port Combination Protocol
D. Link Aggregation Control Protocol


Answer Clike
Which statement about the use of PAgP link aggregation on a Cisco switch that is running Cisco IOS Software is true?

Which statement about the use of PAgP link aggregation on a Cisco switch that is running Cisco IOS Software is true?
A. PAgP modes are off, auto, desirable, and on. Only the combinations auto-desirable, desirabledesirable, and on-on allow the formation of a channel.
B. PAgP modes are active, desirable, and on. Only the combinations active-desirable, desirabledesirable, and on-on allow the formation of a channel.
C. PAgP modes are active, desirable, and on. Only the combinations active-active, desirabledesirable, and on-on allow the formation of a channel.
D. PAgP modes are off, active, desirable, and on. Only the combinations auto-auto, desirabledesirable, and on-on allow the formation of a channel.


Answer Clike
Which action allows interface G0/1 to always actively forward traffic in the port-channel?

A network engineer configured a fault-tolerance link on Gigabit Ethernet links G0/1, G0/2, G0/3, and G0/4 between two switches using Ethernet port-channel. Which action allows interface G0/1 to always actively forward traffic in the port-channel?
A. Configure G0/1 as half duplex and G0/2 as full duplex.
B. Configure LACP port-priority on G0/1 to 1.
C. Configure LACP port-priority on G0/1 to 65535.
D. LACP traffic goes through G0/4 because it is the highest interface ID.


Answer Clike
How many bytes are added to each frame as a result of the configuration?

Refer to the exhibit. How many bytes are added to each frame as a result of the configuration?
A. 4-bytes except the native VLAN
B. 8-bytes except the native VLAN
C. 4-bytes including native VLAN
D. 8-bytes including native VLAN


Answer Clike
What is required for a LAN switch to support 802.1q Q-in-Q encapsulation?

What is required for a LAN switch to support 802.1q Q-in-Q encapsulation?
A. Support less than 1500 MTU
B. Support 1504 MTU or higher
C. Support 1522 layer 3 IP and IPX packet
D. Support 1547 MTU only


Answer Clike
Which action allows a network engineer to limit a default VLAN from being propagated across all trunks?

Which action allows a network engineer to limit a default VLAN from being propagated across all trunks?
A. Upgrade to VTP version 3 for advanced feature set support.
B. Enable VTP pruning on the VTP server.
C. Manually prune default VLAN with switchport trunk allowed vlans remove.
D. Use trunk pruning vlan 1.


Answer Clike
Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a switch?

Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a switch?
A. VLANs 1-1001
B. VLANs 1-4094
C. VLANs 2-1001
D. VLANs 2-4094


Answer Clike
In which portion of the frame is the 802.1q header found?

In which portion of the frame is the 802.1q header found?
A. within the Ethernet header
B. within the Ethernet payload
C. within the Ethernet FCS
D. within the Ethernet source MAC address


Answer Clike
Which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?

Which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?
A. portfast
B. port-security
C. spanning tree
D. storm control


Answer Clike
Which option shows the expected result if a show vlan command is issued?

Refer to the exhibit. Which option shows the expected result if a show vlan command is issued?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_017
D. 300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_018


Answer Clike
What is the maximum number of VLANs that can be assigned to an access switchport without a voice VLAN?

What is the maximum number of VLANs that can be assigned to an access switchport without a voice VLAN?
A. 0
B. 1
C. 2
D. 1024


Answer Clike
What is the size of the VLAN field inside an 802.1q frame?

What is the size of the VLAN field inside an 802.1q frame?
A. 8-bit
B. 12-bit
C. 16-bit
D. 32-bit


Answer Clike
Which VTP mode is needed to configure an extended VLAN, when a switch is configured to use VTP versions 1 or 2?

Which VTP mode is needed to configure an extended VLAN, when a switch is configured to use VTP versions 1 or 2?
A. transparent
B. client
C. server
D. Extended VLANs are only supported in version 3 and not in versions 1 or 2.


Answer Clike
Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?

Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?
A. CDP is enabled by default and can be disabled globally with the command no cdp run.
B. CDP is disabled by default and can be enabled globally with the command cdp enable.
C. CDP is enabled by default and can be disabled globally with the command no cdp enable.
D. CDP is disabled by default and can be enabled globally with the command cdp run.


Answer Clike
What is the default interval at which Cisco devices send Cisco Discovery Protocol advertisements?

What is the default interval at which Cisco devices send Cisco Discovery Protocol advertisements?
A. 30 seconds
B. 60 seconds
C. 120 seconds
D. 300 seconds


Answer Clike
Which option lists the modes that are available for configuring UDLD on a Cisco switch?

Which option lists the modes that are available for configuring UDLD on a Cisco switch?
A. normal and aggressive
B. active and aggressive
C. normal and active
D. normal and passive
E. normal and standby


Answer Clike
Which statement about the UDLD protocol is true?

Which statement about the UDLD protocol is true?
A. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.
B. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.
C. UDLD is a standardized Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.
D. UDLD is a standardized Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.


Answer Clike
Which option describes a limitation of LLDP?

Which option describes a limitation of LLDP?
A. LLDP cannot provide information about VTP.
B. LLDP does not support TLVs.
C. LLDP can discover only Windows servers.
D. LLDP can discover up to two devices per port.


Answer Clike
Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?

Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?
A. native VLAN IDs, port-duplex, hardware platform
B. native VLAN IDs, port-duplex, memory errors
C. native VLAN IDs, memory errors, hardware platform
D. port-duplex, hardware platform, memory errors


Answer Clike
Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?

Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?
A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.
B. Each device broadcasts periodic advertisements to all of its neighbors.
C. Each device sends periodic advertisements to a central device that builds the network topology.
D. Each device sends periodic advertisements to all IP addresses in its ARP table.


Answer Clike
Which statement about LLDP-MED is true?

Which statement about LLDP-MED is true?
A. LLDP-MED is an extension to LLDP that operates between endpoint devices and network devices.
B. LLDP-MED is an extension to LLDP that operates only between network devices.
C. LLDP-MED is an extension to LLDP that operates only between endpoint devices.
D. LLDP-MED is an extension to LLDP that operates between routers that run BGP.


Answer Clike
What is the default value for the errdisable recovery interval in a Cisco switch?

What is the default value for the errdisable recovery interval in a Cisco switch?
A. 30 seconds
B. 100 seconds
C. 300 seconds
D. 600 seconds


Answer Clike
Which option is a possible cause for an errdisabled interface?

Which option is a possible cause for an errdisabled interface?
A. routing loop
B. cable unplugged
C. STP loop guard
D. security violation


Answer Clike
When is a syslog message generated?

If a network engineer applies the command mac-address-table notification mac-move on a Cisco switch port, when is a syslog message generated??
A. A MAC address or host moves between different switch ports.
B. A new MAC address is added to the content-addressable memory.
C. A new MAC address is removed from the content-addressable memory.
D. More than 64 MAC addresses are added to the content-addressable memory.


Answer Clike
What is the default period of time after which a MAC address ages out and is discarded?

In a Cisco switch, what is the default period of time after which a MAC address ages out and is discarded?
A. 100 seconds
B. 180 seconds
C. 300 seconds
D. 600 seconds


Answer Clike
Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?

Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?
A. VLAN
B. default
C. access
D. routing


Answer Clike
Which SDM template disables routing and supports the maximum number of unicast MAC addresses?

Which SDM template disables routing and supports the maximum number of unicast MAC addresses?
A. VLAN
B. access
C. default
D. routing


Answer Clike
Which statement about the use of SDM templates in a Cisco switch is true?

Which statement about the use of SDM templates in a Cisco switch is true?
A. SDM templates are used to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hosts in one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users to manage the flow of traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.


Answer Clike
Which Spanning Tree Protocol should be used to reduce switch resources and managerial burdens that are associated with multiple spanning-tree instances?

A network engineer is setting up a new switched network. The network is expected to grow and add many new VLANs in the future. Which Spanning Tree Protocol should be used to reduce switch resources and managerial burdens that are associated with multiple spanning-tree instances?
A. RSTP
B. PVST
C. MST
D. PVST+
E. RPVST+


Answer Clike
Which option decreases consumption of bandwidth used by broadcast traffic?

While troubleshooting a network outage, a network engineer discovered an unusually high level of broadcast traffic coming from one of the switch interfaces. Which option decreases consumption of bandwidth used by broadcast traffic?
A. storm control
B. SDM routing
C. Cisco IOS parser
D. integrated routing and bridging
E. Dynamic ARP Inspection


Answer Clike
Which statement describes what happens when a domain name is configured on one of the switches?

A new network that consists of several switches has been connected together via trunking interfaces. If all switches currently have the default VTP domain name “null”, which statement describes what happens when a domain name is configured on one of the switches?
A. The switch with the non-default domain name restores back to “null” upon reboot.
B. Switches with higher revision numbers does not accept the new domain name.
C. VTP summary advertisements are sent out of all ports with the new domain name.
D. All other switches with the default domain name become VTP clients.


Answer Clike
Which command does a network engineer use to verify the spanning-tree status for VLAN 10?

Which command does a network engineer use to verify the spanning-tree status for VLAN 10?
A. switch# show spanning-tree vlan 10
B. switch# show spanning-tree bridge
C. switch# show spanning-tree brief
D. switch# show spanning-tree summary
E. switch# show spanning-tree vlan 10 brief


Answer Clike
Which spanning-tree feature satisfies this requirement?

For client server failover purposes, the application server team has indicated that they must not have the standard 30 second delay before their switchport enters a forwarding state. For their disaster recovery feature to operate successfully, they require the switchport to enter a forwarding state immediately. Which spanning-tree feature satisfies this requirement?
A. Rapid Spanning-Tree
B. Spanning-Tree Timers
C. Spanning-Tree FastPort
D. Spanning-Tree PortFast
E. Spanning-Tree Fast Forward


Answer Clike
Which option can be configured to accomplish this?

A manager tells the network engineer to permit only certain VLANs across a specific trunk interface. Which option can be configured to accomplish this?
A. allowed VLAN list
B. VTP pruning
C. VACL
D. L2P tunneling


Answer Clike
Which protocol does the network engineer configure on both devices to accomplish this?

A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?
A. IRDP
B. LLDP
C. NDP
D. LLTD


Answer Clike
Which two commands help trace this PC when the MAC address is known?

The network monitoring application alerts a network engineer of a client PC that is acting as a rogue DHCP server. Which two commands help trace this PC when the MAC address is known? (Choose two.)
A. switch# show mac address-table
B. switch# show port-security
C. switch# show ip verify source
D. switch# show ip arp inspection
E. switch# show mac address-table address


Answer Clike
Which command accomplishes this task?

After port security is deployed throughout an enterprise campus, the network team has been overwhelmed with port reset requests. They decide to configure the network to automate the process of re-enabling user ports. Which command accomplishes this task?
A. switch(config)# errdisable recovery interval 180
B. switch(config)# errdisable recovery cause psecure-violation
C. switch(config)# switchport port-security protect
D. switch(config)# switchport port-security aging type inactivity
E. switch(config)# errdisable recovery cause security-violation


Answer Clike
Which option must be enabled to allow for enhanced reporting mechanisms using Cisco Discovery Protocol?

While doing network discovery using Cisco Discovery Protocol, it is found that rapid error tracking is not currently enabled. Which option must be enabled to allow for enhanced reporting mechanisms using Cisco Discovery Protocol?
A. Cisco Discovery Protocol version 2
B. Cisco IOS Embedded Event Manager
C. logging buffered
D. Cisco Discovery Protocol source interface
E. Cisco Discovery Protocol logging options


Answer Clike
What is causing the line protocol on this interface to be shown as down?

Refer to the exhibit. A network engineer investigates a recent network failure and notices that one of the interfaces on the switch is still down. What is causing the line protocol on this interface to be shown as down?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_009
A. There is a layer 1 physical issue.
B. There is a speed mismatch on the interface.
C. The interface is configured as the target of the SPAN session.
D. The interface is configured as the source of the SPAN session.
E. There is a duplex mismatch on the interface.


Answer Clike
Which action must be done to apply a new load balancing method?

A network engineer must set the load balance method on an existing port channel. Which action must be done to apply a new load balancing method?
A. Configure the new load balancing method using port-channel load-balance.
B. Adjust the switch SDM back to “default”.
C. Ensure that IP CEF is enabled globally to support all load balancing methods.
D. Upgrade the PFC to support the latest load balancing methods.


Answer Clike
Which two elements are used to accomplish this?

A network engineer must adjust the STP interface attributes to influence root port selection.
Which two elements are used to accomplish this? (Choose two.)
A. port-priority
B. cost
C. forward-timers
D. link type
E. root guard


Answer Clike
Which spanning-tree technology is used to accomplish backup root port selection?

Pilot testing of the new switching infrastructure finds that when the root port is lost, STP immediately replaces the root port with an alternative root port. Which spanning-tree technology is used to accomplish backup root port selection?
A. PVST+
B. PortFast
C. BackboneFast
D. UplinkFast
E. Loop Guard
F. UDLD


Answer Clike
After reviewing UDLD status on switch ports, an engineer notices that the current bidirectional state for an access port is “Unknown.” Which statement describes what this indicates about the status of the port?

After reviewing UDLD status on switch ports, an engineer notices that the current bidirectional state for an access port is “Unknown.” Which statement describes what this indicates about the status of the port?
A. The port is fully operational and no known issues are detected.
B. The bidirectional status of “unknown” indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.
C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.
D. The UDLD port is placed in the “unknown” state for 5 seconds until the next UDLD packet is received on the interface.


Answer Clike
Which option describes what causes the port to go into the errdisable state?

After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.


Answer Clike
In which three ways does this command impact the traffic?

The command storm-control broadcast level 75 65 is configured under the switch port connected to the corporate mail server. In which three ways does this command impact the traffic? (Choose three.)
A. SNMP traps are sent by default when broadcast traffic reaches 65% of the lower-level threshold.
B. The switchport is disabled when unicast traffic reaches 75% of the total interface bandwidth.
C. The switch resumes forwarding broadcasts when they are below 65% of bandwidth.
D. Only broadcast traffic is limited by this particular storm control configuration.
E. Multicast traffic is dropped at 65% and broadcast traffic is dropped at 75% of the total interface bandwidth.
F. The switch drops broadcasts when they reach 75% of bandwidth.


Answer Clike
Which option is the cause of the problem?

A switch is added into the production network to increase port capacity. A network engineer is configuring the switch for DHCP snooping and IP Source Guard, but is unable to configure ip verify source under several of the interfaces. Which option is the cause of the problem?
A. The local DHCP server is disabled prior to enabling IP Source Guard.
B. The interfaces are configured as Layer 3 using the no switchport command.
C. No VLANs exist on the switch and/or the switch is configured in VTP transparent mode.
D. The switch is configured for sdm prefer routing as the switched database management template.
E. The configured SVIs on the switch have been removed for the associated interfaces.


Answer Clike
Which option is the cause of this issue?

A DHCP configured router is connected directly to a switch that has been provisioned with DHCP snooping. IP Source Guard with the ip verify source port-security command is configured under the interfaces that connect to all DHCP clients on the switch. However, clients are not receiving an IP address via the DHCP server. Which option is the cause of this issue?
A. The DHCP server does not support information option 82.
B. The DHCP client interfaces have storm control configured.
C. Static DHCP bindings are not configured on the switch.
D. DHCP snooping must be enabled on all VLANs, even if they are not utilized for dynamic address allocation.


Answer Clike
What is a cause for this issue?

An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?
A. VLAN filters are required to ensure traffic mirrors effectively.
B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.
C. The port channel can be used as a SPAN source, but not a destination.
D. RSPAN must be used to capture EtherChannel bidirectional traffic.


Answer Clike
What is the root cause of this issue?

A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?
A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.


Answer Clike
What solution allows the network switch to automatically recover from such an issue?

While working in the core network building, a technician accidently bumps the fiber connection between two core switches and damages one of the pairs of fiber. As designed, the link was placed into a non-forwarding state due to a fault with UDLD. After the damaged cable was replaced, the link did not recover. What solution allows the network switch to automatically recover from such an issue?
A. macros
B. errdisable autorecovery
C. IP Event Dampening
D. command aliases
E. Bidirectional Forwarding Detection


Answer Clike
What effect does the mac address-table aging-time 180 command have on the MAC addresstable?

What effect does the mac address-table aging-time 180 command have on the MAC addresstable?
A. This is how long a dynamic MAC address will remain in the CAM table.
B. The MAC address-table will be flushed every 3 minutes.
C. The default timeout period will be 360 seconds.
D. ARP requests will be processed less frequently by the switch.
E. The MAC address-table will hold addresses 180 seconds longer than the default of 10 minutes.


Answer Clike
Which technique automatically limits VLAN traffic to only the switches that require it?

Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR


Answer Clike
What is the reason for this?

An administrator recently configured all ports for rapid transition using PortFast. After testing, it has been determined that several ports are not transitioning as they should. What is the reason for this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.


Answer Clike
After the recent upgrade of the switching infrastructure, the network engineer notices that the port roles that were once “blocking” are now defined as “alternate” and “backup.” What is the reason for this change?

After the recent upgrade of the switching infrastructure, the network engineer notices that the port roles that were once “blocking” are now defined as “alternate” and “backup.” What is the reason for this change?
A. The new switches are using RSTP instead of legacy IEEE 802.1D STP.
B. IEEE 802.1D STP and PortFast have been configured by default on all newly implemented Cisco Catalyst switches.
C. The administrator has defined the switch as the root in the STP domain.
D. The port roles have been adjusted based on the interface bandwidth and timers of the new Cisco Catalyst switches.


Answer Clike
What would cause this issue?

Refer to the exhibit. Switch A, B, and C are trunked together and have been properly configured for VTP. Switch B has all VLANs, but Switch C is not receiving traffic from certain VLANs. What would cause this issue?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_003
A. A VTP authentication mismatch occurred between Switch A and Switch
B. B. The VTP revision number of Switch B is higher than that of Switch A.
C. VTP pruning is configured globally on all switches and it removed VLANs from the trunk interface that is connected to Switch C.
D. The trunk between Switch A and Switch B is misconfigured.


Answer Clike
What is the most probable cause of this behavior?

Refer to the exhibit. Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?
300-115-implementing-cisco-ip-switched-networks-switch-v2-0_img_003
A. Switch B is configured in transparent mode.
B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.
C. The VTP revision number of the Switch B is higher than that of Switch A.
D. The trunk between Switch A and Switch B is misconfigured.


Answer Clike
What should be configured for extended VLANs?

After implementing VTP, the extended VLANs are not being propagated to other VTP switches.
What should be configured for extended VLANs?
A. VTP does not support extended VLANs and should be manually added to all switches.
B. Enable VTP version 3, which supports extended VLAN propagation.
C. VTP authentication is required when using extended VLANs because of their ability to cause network instability.
D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.


Answer Clike
What must be done to fix this?

Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version. However, VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be done to fix this?
A. Remove the VTP domain name from all switches with “null” and then replace it with the new domain name.
B. Configure a different native VLAN on all new switches that are configured as VTP clients.
C. Provision one of the new switches to be the VTP server and duplicate information from the existing network.
D. Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.


Answer Clike
Which vendor-neutral protocol could be used to resolve this issue?

After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol


Answer Clike
What would cause the output to show only the single neighbor?

A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships. What would cause the output to show only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.


Answer Clike
What is the result of the implemented command?

Interface FastEthernet0/1 is configured as a trunk interface that allows all VLANs.
This command is configured globally:
monitor session 2 filter vlan 1 – 8, 39, 52
What is the result of the implemented command?
A. All VLAN traffic is sent to the SPAN destination interface.
B. Traffic from VLAN 4 is not sent to the SPAN destination interface.
C. Filtering a trunked SPAN port effectively disables SPAN operations for all VLANs.
D. The trunk’s native VLAN must be changed to something other than VLAN 1.
E. Traffic from VLANs 1 to 8, 39, and 52 is replicated to the SPAN destination port.


Answer Clike
What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?

An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?
A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.


Answer Clike